Common Material Instructions For Plate Heat Exchanger Plates

Jul 01, 2024 Leave a message

In plate heat exchangers, it is important to select the appropriate material for the plates based on the different heat exchange media, as the different media involved in heat transfer can corrode the corresponding plates.
1: 904L and SUS890L stainless steel
This is a cost-effective austenitic stainless steel that balances price and corrosion resistance. It has good corrosion resistance and is particularly suitable for general acids and halides such as sulfuric acid and phosphoric acid (containing Cl -, F -). Due to its high content of Cr, Ni, and Mo, it has good resistance to stress corrosion, pitting corrosion, and crevice corrosion. Applicable conditions in chlorine containing media.
2: 254 SMO premium stainless steel
The ultra-low carbon advanced stainless steel improved by increasing the Mo content of 316 type has excellent resistance to chloride pitting and crevice corrosion, and is suitable for media such as saltwater and inorganic acids that cannot use 316 type.
3: Titanium
Non alloyed titanium is lightweight with a density of 4.51. It can naturally generate a passivation protective film (Ti2O3) and has "self-healing" properties if damaged. Therefore, its corrosion resistance is better than stainless steel, making it a typical material suitable for chlorine containing media (Cl - concentration>200mg/L, temperature ≤ 130 ℃). In seawater and other chloride solutions (such as CaCl2) not exceeding 120 ℃, it is actually not corroded. Generally, it can be used for seawater below 135 ℃ and various concentrations of saltwater (NaCl) below 165 ℃.
Titanium also has good corrosion resistance in organic acids below boiling point (such as concentrated nitric acid, concentrated carbonic acid, etc.) and dilute alkaline solutions.
Titanium has poor corrosion resistance in H2SO4, HCl, HF, and aqua regia. In certain concentrated chloride solutions at high temperatures (above 120 ℃), such as wastewater with pH>7 and chloride concentration>200mg/L, crevice corrosion or stress corrosion may also occur. At this point, titanium palladium alloy should be selected.
4: Titanium palladium alloy
This is non alloyed titanium with added palladium (0.12%~0.25%), which significantly improves the corrosion resistance of titanium in acidic media, especially under less stringent conditions. For example, it has good corrosion resistance to nitric acid with a concentration of 70%, hydrochloric acid containing oxidizing ions (such as Fe+, Cu+), and electroplating solutions. In addition, it can also be used for dilute sulfuric acid with a concentration of ≤ 10% and a temperature of ≤ 70 ℃.
5: Nickel 200
This is a pure nickel plate containing over 99% nickel. Mainly used for high concentration (50%~70%), high temperature (up to boiling point) caustic alkali solutions (NaOH, KOH, etc.). However, it is sensitive to crevice corrosion caused by chlorides such as brackish water.
6: Hastelloy C-276
Has good corrosion resistance: almost unaffected by Cl -; Excellent corrosion resistance to various concentrations of sulfuric acid, it is one of the few materials that can be used for hot concentrated sulfuric acid; Widely used for organic acids (such as formic acid, acetic acid), high-temperature HF acids, and certain concentrations of hydrochloric acid (<40%), phosphoric acid (≤ 50%); Chloride, fluoride, and organic solvents such as methanol and ethanol.
7: Monel 400
Ni (about 70%) - Cu (about 30%) nickel based alloy. In non aerated sulfuric acid with a concentration below 80% and a temperature not exceeding 50 ℃~100 ℃, HF acid with a concentration below 50% and a temperature below 100 ℃, acetic acid, and caustic alkali, the corrosion resistance is good. Specially suitable for acidic chloride solutions and certain working conditions of brackish water and saltwater; Has good high temperature resistance. But it is not suitable for concentrated sulfuric acid, hydrochloric acid, and nitric acid, and is sensitive to the corrosion of mercury (sometimes present as an impurity).
8: Incoloy825
Suitable for sulfuric acid of various concentrations at low temperatures; In a solution of caustic alkali (such as NaOH) with a concentration of 50%~70%, it has good corrosion resistance and does not produce stress corrosion cracking. However, it is very sensitive to crevice corrosion caused by chloride. In addition, the stamping performance is not very good, so it is not a commonly used material for sheet metal.